Pinene II

Qty Discounts New Price
1-3 $57.95	4-7 $54.95	8+ $49.95

Volume discounts!! - The more you buy the more you save!
On orders over $1,000.00 receive a 5% discount. On orders over $2,500.00 receive a 7% discount!

Pinene II (1.25 Gallons)

Sticker, Spreader, Extender, Adjuvant, Surfactant. Compare to Nufilm

Pinene II is an Extender Sticker Spreader designed to extend the life of pesticides. It may be used with all pesticide products and soluble fertilizers. Pinene II forms a durable film that holds a pesticide on the crop foliage. This shield greatly reduces the effects of environmental factors, such as rain, which may decrease the effectiveness of pesticides. Pinene II will not foam, freeze or clog nozzles. It may be applied by aerial, ground or concentrate sprayer. It enhances the initial pesticide application to give complete coverage. Pinene II prevents the removal of the pesticides from the leaf surface by rainfall and wind. It screens the pesticide spray residue from ultraviolet rays which often cause pesticide degradation. Pesticide volatilization is minimized by the protective shield. Under most conditions, apply sprays containing Pinene II and allow at least one hour of daylight before an anticipated rain.

Functions and Benefits:

Recommended for use with all pesticide products and soluble fertilizers.
Forms a durable film that holds a pesticide on the crop foliage.
Helps penetrate and spread pesticides over foliage.
Prevents the removal of pesticides from the leaf surface by wind and rainfall.
Reduces pesticide volatilization.
Screens the pesticide residue from ultraviolet rays which often cause pesticide degradation.
Will not foam or clog nozzles.

Frequently Asked Questions about Pinene II:

How closely to harvest can you apply Pinene II with tolerance exempt pesticides?

If timing is a concern, you should use a reduced rate or not use pinene. The exact number of days will depend on environmental conditions.

Does time of day affect the application of Pinene II?

Under most conditions, apply sprays containing Pinene II with at least one hour of daylight so the protective shield can set.

Approximate use rate: Varies - See label for specific instructions.

DIRECTIONS FOR USE

To extend the activity and increase the efficiency of insecticidal and fungicidal sprays when applied by aircraft or ground equipment: Use 1-2 pint of this product per acre.
Hydraulic gun or air blast sprayer applications to Shade, Fruit and Nut trees (dilute): Use 6 to 8 fluid ounces of this product per 100 gallons of water.
Dilute application of Citrus sprays when spray volume is 1,000 to 1,500 gallons per acre: Use 2 pints of this product per 500 gallons of spray mix.
Concentrate sprays when spray volume is approximately 100 gallons or less per acre: Use 1 pint of this product per acre.
Turf applications: Use 8 to 16 fluid ounces per acre.
Vegetable and Cotton programs: Use 4 to 16 fluid ounces of this product per acre.
Pears: Use 2 pints per acre on Pears prior to cluster bud in no less than 200 gallons of water.
This product used at the rate of 4-8 fluid ounces per acre enhances the sticking activity of insecticides and fungicides.
Use in spray tank combination with insecticides and fungicides.
Do not apply this product to food crops within 30 days of harvest except as follows: This product can be used with copper fungicides, Bacillus thuringiensis products and other tolerance exempt pesticides on food crops up to harvest.
Always consult the label of the Herbicide, Insecticide or Fungicide to be used before adding Pinene II.

MIXING DIRECTIONS

To ensure good emulsification, pre-mix this product with water before adding to spray tank. Add this product to the spray tank as the last ingredient, as the spray tank is filling, with the agitator running. Always rinse tank, lines and nozzles with water immediately after spraying. After rinsing, a small amount of sticky residue may remain in the spray tank. This residue can help to prevent rust and corrosion and will not clog nozzles when sprayer is next used. If spray drift sets down on unintended surfaces, it can be removed with soap and water, before the spray residue is dry or with premium grade kerosene after the film has dried. To remove dried deposits from painted car surfaces, use standard tar remover products designed for use on painted car finishes.

PRINCIPAL FUNCTIONING AGENTS:

Polymeric terpenes.......96.0%

CONSTITUENTS INEFFECTIVE AS SPRAY ADJUVANTS.......4.0%

TOTAL.......100.0%

Pinene II Label

Pinene II MSDS

No species controlled by this product.

Pinene II is labeled for use on the following areas but always consult the label for specific information.

Citrus
Cotton
Fruit Trees
Nut Trees
Pears
Shade Trees
Turf Vegetables

If your state is not listed, there are no restrictions in your state.
Restrictions	State
Restricted - No sales to State:	AS
Restricted - No sales to State:	AA
Restricted - No sales to State:	AE
Restricted - No sales to State:	AP
Restricted - No sales to State:	FM
Restricted - No sales to State:	GU
Restricted - No sales to State:	ME
Restricted - No sales to State:	MH
Restricted - No sales to State:	NH
Restricted - No sales to State:	NY
Restricted - No sales to State:	MP
Restricted - No sales to State:	PW
Restricted - No sales to State:	PR
Restricted - No sales to State:	UT
Restricted - No sales to State:	VI

Categories

Information

Pinene II - 1.25 gallon (Sticker-Spreader-Extender)

Price:

Price: $57.95

Pinene II

Pinene II is labeled for use on the following areas but always consult the label for specific information.

Customers who bought this product also purchased...

Specials

Notifications